SIPLUS extreme RAIL interface modules

• Заказные данные
  (2)
• Аксессуары
  (2)
• Информационные материалы

  Информационные материалы

  Thanks to their wide scope of functions, the interface modules of the scalable SIPLUS extreme RAIL ET 200SP I/O system, even in their basic versions, cover a wide range of applications. The basic functions of the interface modules include:

  • Approved in accordance with the railway standards EN 50155, EN 15121, EN 50124, EN 50125 and EN 45545 for use in rail traffic
  • Short data update times of typically 1 ms
  • Single Hot Swap (withdrawing and insertion of an I/O module during operation without impairing the communication with the remaining modules)
  • Operation with gaps (empty BaseUnits)
  • Complete diagnostic support, extending to channel-by-channel diagnostics
  • Configuration control / option handling (adaptation of the actual configuration via user software)
  • Device replacement without PG I&M data 0 to 3 (electronic rating plate with non-volatile storage of plant data)
  • Firmware update
  • Pluggable 24 V DC supply connection
  • Network / power failure bridging time of 5 ms
  • Labeling option via optional labeling strips and equipment labeling plates

  When using PROFINET interface modules, the following basic functions are also included:

  • Media redundancy (MRP) integrated 2-port switch
  • Freely selectable connection method via SIMATIC BusAdapter
  • Reset button for simple return to factory settings without the need for programming device
  • Replacement without programming device even in case of non-topological configuration with subsequent automatic launching
  • Automatic synchronization of the backplane bus to the PROFINET cycle to minimize the response time fluctuations (jitter)

  SIPLUS ET 200SP IM 155-6PN ST BA TX RAIL with PROFINET interface

  • Max. 32 I/O modules, also PROFIsafe modules with complete diagnostic support.
  • Max. 244 bytes in each case for input and output data per module and per station
  • Data update time: typ. 5 ms
  • PROFIBUS connection via 9-pin SUB-D female connector
  • Package inclusive of server module and PROFIBUS connector with programming device socket

  Область применения

  The SIPLUS ET 200SP IM 155-6PN ST BA TX RAIL is designed mainly for standard PROFINET applications with average station expansion of up to 32 modules (max. 512 IO signals). All I/O modules, including PROFIsafe, can be used.

  Дизайн

  The SIPLUS ET 200SP IM 155-6PN ST BA TX RAIL interface module is snapped directly onto the standard mounting rail (7.5 x 35 mm or 15 x 35 mm).

  • Optional labeling using light gray or yellow labeling strips. There is a choice of 2 materials:
    • Film strips on a roll with 500 strips, for thermal transfer roll printer
    • Card (180 g/m²), DIN A4 sheets with 100 strips each, for laser printer
  • Optional equipment marking using slide-in equipment labeling plates
  • Different connection types of the PROFINET by means of SIMATIC BusAdapter
    • Under ambient conditions in accordance with SIMATIC standard using BA 2xRJ45 for connection via RJ45 plug
    • In the case of mechanical loading during operation and/or an increased EMC requirements BA 2xFC for direct connection of the PROFINET cable

  Технические данные

  Order number		6AG2155-6AA00-4BN0	6AG2155-6AU00-4BN0
  		SIPLUS ET 200SP IM155-6PN ST BA TX RAIL	SIPLUS ET 200SP IM155-6PN ST TX RAIL
  General information
  Product type designation		IM 155-6 PN ST with BA 2xRJ45 and server module	IM 155-6 PN ST with server module
  Product function
  ● I&M data		Yes; I&M0 to I&M3	Yes; I&M0 to I&M3
  Supply voltage
  Rated value (DC)		24 V	24 V
  Reverse polarity protection		Yes	Yes
  Mains buffering
  ● Mains/voltage failure stored energy time		5 ms	5 ms
  Hardware configuration
  Rack
  ● Modules per rack, max.		32; + 16 ET 200AL modules	32; + 16 ET 200AL modules
  Submodules
  ● Number of submodules per station, max.		256	256
  Interfaces
  Number of PROFINET interfaces		1; 2 ports (switch)	1; 2 ports (switch)
  1. Interface
  Interface types
  ● Number of ports		2	2
  ● integrated switch		Yes	Yes
  ● RJ 45 (Ethernet)		Yes; Pre-assembled BusAdapter BA 2x RJ45
  ● BusAdapter (PROFINET)		Yes; Applicable BusAdapter: BA 2x RJ45, BA 2x FC	Yes; Applicable BusAdapter: BA 2x RJ45, BA 2x FC
  Functionality
  ● PROFINET IO Device		Yes	Yes
  ● Open IE communication		Yes	Yes
  ● Media redundancy		Yes; PROFINET MRP	Yes; PROFINET MRP
  Interface types
  RJ 45 (Ethernet)
  ● Transmission procedure		PROFINET with 100 Mbit/s full duplex (100BASE-TX)	PROFINET with 100 Mbit/s full duplex (100BASE-TX)
  ● 10 Mbps		Yes; for Ethernet services	Yes; for Ethernet services
  ● 100 Mbps		Yes; PROFINET with 100 Mbit/s full duplex (100BASE-TX)	Yes; PROFINET with 100 Mbit/s full duplex (100BASE-TX)
  ● Autonegotiation		Yes	Yes
  ● Autocrossing		Yes	Yes
  PROFINET IO Device
  Services
  — Isochronous mode		No	No
  — Open IE communication		Yes	Yes
  — IRT		Yes; with send cycles of between 250 µs and 4 ms in increments of 125 µs	Yes; with send cycles of between 250 µs and 4 ms in increments of 125 µs
  — MRP		Yes	Yes
  — MRPD		No	No
  — PROFINET system redundancy		No	No
  — PROFIenergy		Yes	Yes
  — Prioritized startup		Yes	Yes
  — Shared device		Yes	Yes
  — Number of IO Controllers with shared device, max.		2	2
  Open IE communication
  ● TCP/IP		Yes	Yes
  ● SNMP		Yes	Yes
  ● LLDP		Yes	Yes
  Isochronous mode
  Isochronous operation (application synchronized up to terminal)		No	No
  Interrupts/diagnostics/status information
  Status indicator		Yes	Yes
  Alarms		Yes	Yes
  Diagnostic functions		Yes	Yes
  Diagnostics indication LED
  ● RUN LED		Yes; Green LED	Yes; Green LED
  ● ERROR LED		Yes; Red LED	Yes; Red LED
  ● MAINT LED		Yes; yellow LED	Yes; yellow LED
  ● Monitoring of the supply voltage (PWR-LED)		Yes; Green LED	Yes; Green LED
  ● Connection display LINK TX/RX		Yes; 2x green link LEDs on BusAdapter	Yes; 2x green link LEDs on BusAdapter
  Isolation
  Isolation tested with		707 V DC (type test) and according to EN 50155 (routine test)	707 V DC (type test) and according to EN 50155 (routine test)
  Standards, approvals, certificates
  Network loading class		2	2
  Security level		According to Security Level 1 Test Cases V1.1.1	According to Security Level 1 Test Cases V1.1.1
  Railway application
  ● EN 50121-3-2		Yes; EMC for rail vehicles	Yes; EMC for rail vehicles
  ● EN 50121-4		Yes; EMC for signal and telecommunications systems	Yes; EMC for signal and telecommunications systems
  ● EN 50124-1		Yes; Railway applications - overvoltage category OV2; pollution degree PD2; rated surge voltage UNi = 0.5 kV; UNm = 24 V DC	Yes; Railway applications - overvoltage category OV2; pollution degree PD2; rated surge voltage UNi = 0.5 kV; UNm = 24 V DC
  ● EN 50125-1		Yes; Rail vehicles - see ambient conditions	Yes; Rail vehicles - see ambient conditions
  ● EN 50125-2		Yes; Stationary electrical equipment - see ambient conditions	Yes; Stationary electrical equipment - see ambient conditions
  ● EN 50125-3		Yes; Signal and telecommunications systems - see ambient conditions; vibrations and shocks: Application point outside of tracks (1 m to 3 m away from track)	Yes; Signal and telecommunications systems - see ambient conditions; vibrations and shocks: Application point outside of tracks (1 m to 3 m away from track)
  ● EN 50155		Yes; Rail vehicles - temperature class Tx, horizontal mounting position, salt spray Class ST2	Yes; Rail vehicles - temperature class Tx, horizontal mounting position, salt spray Class ST2
  ● EN 61373		Yes; Rail vehicles - vibrations and shocks: Category 1 Class A/B	Yes; Rail vehicles - vibrations and shocks: Category 1 Class A/B
  ● Fire protection acc. to EN 45545-2		Yes; Rail vehicles - verification on request	Yes; Rail vehicles - verification on request
  Ambient conditions
  Ambient temperature during operation
  ● horizontal installation, min.		-40 °C; = Tmin	-40 °C; = Tmin
  ● horizontal installation, max.		70 °C; = Tmax; +85 °C for 10 min (Tx acc. to EN 50155)	70 °C; = Tmax; +85 °C for 10 min (Tx acc. to EN 50155)
  Extended ambient conditions
  ● relative to ambient temperature-atmospheric pressure-installation altitude		Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m)	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m)
  Relative humidity
  — With condensation, tested in accordance with IEC 60068-2-38, max.		100 %; RH incl. condensation/frost (no commissioning under condensation conditions)	100 %; RH incl. condensation/frost (no commissioning under condensation conditions)
  Resistance
  — against biologically active substances / conformity with EN 60721-3-3		Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation!
  — against biologically active substances/conformity with EN 60721-3-5		Yes; Class 5B2 mold and fungal spores (excluding fauna). The supplied plug covers must remain in place over the unused interfaces during operation!	Yes; Class 5B2 mold and fungal spores (excluding fauna). The supplied plug covers must remain in place over the unused interfaces during operation!
  — against chemically active substances / conformity with EN 60721-3-3		Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
  — against chemically active substances/conformity with EN 60721-3-5		Yes; Class 5C3 (RH < 75%) including salt spray according to EN 50155 (ST2). The supplied plug covers must remain in place over the unused interfaces during operation!	Yes; Class 5C3 (RH < 75%) including salt spray according to EN 50155 (ST2). The supplied plug covers must remain in place over the unused interfaces during operation!
  — against mechanically active substances / conformity with EN 60721-3-3		Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
  — against mechanically active substances/conformity with EN 60721-3-5		Yes; Class 5S3 including sand and dust. The supplied plug covers must remain in place over the unused interfaces during operation!	Yes; Class 5S3 including sand and dust. The supplied plug covers must remain in place over the unused interfaces during operation!
  Dimensions
  Width		50 mm	50 mm
  Height		117 mm	117 mm
  Depth		74 mm	74 mm
  Weights
  Weight, approx.		191 g; IM155PN ST with BA 2x RJ45 (mounted)	147 g; without BusAdapter
  Other
  Note:		For use in railway applications, also observe the product information "SIPLUS extreme RAIL" A5E37661960A Online Support article 109736776	For use in railway applications, also observe the product information "SIPLUS extreme RAIL" A5E37661960A Online Support article 109736776